Online Assessment вЂ“ NDG Linux Essentials.

NS 1.0 вЂ“ Packet Tracer Activity Lab Answers.

NetEss v1 Student Lab Source Files Answers.

NetEss v1 Packet Tracer Activity Source Files Answers.

NE 2.0 Packet Tracer Activity Lab Answers.

ITN v6 Student Lab Source Files Answers.

ITE v7 Student Lab Source Files Answers.

ITE v6 Student Packet Tracer Source Files Answers.

ITE v6 Student Lab Source Files Answers.

DevNet вЂ“ DEVASC вЂ“ Packet Tracer Lab Answers.

Cybersecurity Student Lab Source Answers.

CyberOps AssociateвЂ“ CA вЂ“ Packet Tracer Answers.

CyberEss v1 Student Lab Source Files Answers.

CyberEss v1 Packet Tracer Activity Source Files Answers.

CCNA3 v7 вЂ“ ENSA вЂ“ Packet Tracer Answers.

CCNA2 v7 вЂ“ SRWE вЂ“ Packet Tracer Answers.

They use the address of the subinterface. What addresses do PC1 and PC3 use as their default gateway addresses? If the configurations are correct, PC1 and PC3 should be able to ping their default gateways and each other.

Issue the show interface trunk command to verify that the interface is configured as a trunk.Д¬lose configuration window Step 3: Test Connectivity.

The interface is no longer listed in the command output. How can you determine that the interface is a trunk port using the show vlan command? S1(config- if)# switchport mode trunk Question:

Because the router was configured with multiple subinterfaces assigned to different VLANs, the switch port connecting to the router must be configured as a trunk.

The switch is not yet configured with a trunk port that is connected to the router.

Verify that the subinterfaces are now active.Д¬lose configuration window Part 3: Test Connectivity with Inter-VLAN Routing Step 1: Ping between PC1 and PC3. Therefore, in order to enable subinterfaces, you must enable the physical interface that they are associated with. Subinterfaces are virtual interfaces that are associated with a physical interface. Use the show ip interface brief command to verify subinterface configuration.R1(config- subif )# encapsulation dot1Q 30 R1(config- subif )# encapsulation dot1Q 10 Refer to the Address Table and assign the correct IP address to the subinterface.Set the encapsulation type to 802.1Q and assign VLAN 10 to the subinterface.

Part 2: Configure Subinterfaces Step 1: Configure subinterfaces on R1 using the 802.1Q encapsulation. The PCs are on different IP networks and require a router or a L ayer 3 switch to provide communication between them. Were the pings successful? Why did you get this result?

Issue the show vlan brief command to verify VLAN configuration.ДЎ default active Fa0/1, Fa0/2, Fa0/3, Fa0/4Д¬lose configuration window Step 3: Test connectivity between PC1 and PC3.

S1(config- if)# switchport access vlan 30 S1(config- if)# switchport access vlan 10

Assign the port connected to PC3 to VLAN 30.

Assign the port connected to PC1 to VLAN 10.

Configure interfaces F0/6 and F0/11 as access ports and assign VLANs.

S1(config- vlan )# vlan 30 Step 2: Assign VLANs to ports. Instructions Part 1: Add VLANs to a Switch Step 1: Create VLANs on S1. You will then enable trunk interfaces and verify connectivity between VLANs. In this activity, you will configure VLANs and inter-VLAN routing. If Routing on switch configured correctly PC0 should be ping PC1 successfully.Part 3: Test Connectivity with Inter-VLAN Routing Scenario R1(config-subif)#interface gigabitEthernet 0/0.200 R1(config-if)#interface gigabitEthernet 0/0.100 Router R1(config)#interface gigabitEthernet 0/0

SW_1(config)#interface gigabitEthernet 0/1 SW_1(config-if)#switchport access vlan 200 SW_1(config-if)#interface fastEthernet 0/11 SW_1(config-if)#switchport access vlan 100 SW_1(config-if)#interface fastEthernet 0/1 Whenever hosts in one VLAN need to communicate with hosts in another VLAN, the traffic must be routed between them. VLANs divide broadcast domains in a LAN environment. Routing on Stick (Inter VLAN Routing) used when we want to make connection between two hosts on different VLAN.

Router on a stick packet tracer